By now you’ve heard the term “selenite tool” a lot.
But what is selenites exactly and how can you make one?
This article has answers.
Aselenites are tiny grains of silicon, a kind of carbon that forms when carbon atoms form on a silicon substrate.
Selenites don’t have an outer shell, which means they’re a solid, hard, and porous material.
It’s a good material for a flare nut because it’s lightweight, easy to make, and can be used to make flares.
These are also the best for making your own flares because the silicon isn’t damaged by the heat of the flare nut.
If you’re using a standard flare nut, you can drill it out with a small drill bit, but selenitic flares are easier.
The seleninite doesn’t oxidize, so they won’t oxidate to lead.
You can use selenide to make flare nuts and they’re even better because they’re also inexpensive.
What you need:1 cup of silicon2 cups of water, enough to cover your drill bit2-3 pounds of sand (to make a rough 1.5 inch circle)2-4 inches of 1/4 inch PVC pipe2 cups or 8 pieces of 1 inch PVC thread (or some similar material)4-5 tablespoons of baking soda (you can use tap water or water from the sink)1 cup or so of selenidane, or a good quality selenate (we use the same brand of serenite as the one that you get at your hardware store)1 teaspoon of salt (to taste)The selenides in the above-mentioned ingredients are all commonly used for making flares and can also be used in some other applications, such as welding.
If your selenized flare nut is a bit flaky, you could try heating it with a bit of water.
That might help soften the plastic and make it easier to shape.
Once you’ve shaped the flare, you’re ready to use it.
First, make sure your drill has a 1/8-inch hole.
The drill bit doesn’t need to be the exact same size as the flare nuts, but you’ll have to make sure that it’s the same size.
Make a rectangle out of the plastic, then drill a hole in the middle of it.
You should make a notch in the plastic so that the flare will fit through the hole.
Now, make a small, flat piece of 1.25-inch PVC pipe.
You’ll want this to be about the size of the pipe you drilled out.
Use this piece to mark where you want to drill the hole in your flare nut and where you’ll drill the flare.
Now, use your drill to make the PVC pipe into a circle.
You want to make this circle about an inch in diameter, so cut a long strip of the PVC to make an appropriate size circle.
Now that you have a flare, cut a piece of ½ inch PVC tubing.
This will be the length of the end of your flare, so you can easily drill out the flare with a drill bit.
Now you’ll want to cut a hole right through the middle so that your flare will go through.
You’ll want a pipe that will pass through your flare so that it fits through the PVC tubing, but not so that you’ll get an obstruction.
Make your flare by using a flange nut or flare cutter.
Once it’s all in place, you’ll need to use the flange to push the flare out of your nut and into the flare tube.
This is easier if you have the flare to the side of the drill bit rather than the center.
Next, make your flare tube, which is the tube that you put the flare into.
This tube should be about ¾-inch wide and ¼-inch deep.
You don’t want to put it too close to the flare because you’ll be bending the flare a little.
Now you’re all done!
Make sure you drill the PVC into the circle as you’re doing so.
You’re now ready to glue the flare together.
Once the flare is all glued in, you should have a nice looking flare.
If it’s not exactly like the photo above, the glue will have to be a little more dry.
The glue will hold it together better, but if you’re making it in one piece, it’s easier to sand it down with sandpaper.
When you’re done, you want your flare to be nice and shiny.
That means you’ll probably need to paint it with some sort of coat or stain to make it look even.
You may have to use some sort, like acetone, to coat the flare for a few days, but it should last.